ServicesMetal Roofing
Metal Roofing in McCordsville
A metal roof is a long-term decision, and it goes best when it is planned rather than rushed. We inspect your current roof, explain which panel system suits your home, and give you a written estimate so you can budget and schedule on your terms.

When Metal Is the Right Call
Metal roofing makes the most sense when you plan to stay in your home for many years and want a roof that sheds snow, resists wind and holds its color. It costs more up front than shingles, so the smart time to look at it is a season or two before your current roof needs replacing, not the week a leak shows up.
We install two main types. Standing seam panels lock together over hidden clips, so no screws pierce the weather surface and the panels can expand and contract through Indiana's freeze-thaw swings. Exposed-fastener panels are screwed through the face, cost less, and suit garages, porches and simpler roofs. We will tell you plainly which one fits your roof and your budget, and if shingle roofing is the better value for your situation, we will say that too.
We are licensed and hold an A+ BBB rating, and we keep our estimates in writing so you can compare options at your kitchen table.
What Goes Into Your New Metal Roof
- Removal down to the deck
- The old roofing comes off completely so we can examine each sheet of decking underneath. Anything soft or delaminated gets replaced before new material goes on, and you receive photos of what we found.
- High-temperature underlayment
- Metal heats up in summer sun, so we lay a synthetic underlayment rated for that heat. Ice and water shield goes along the eaves and in valleys, where melting snow tends to back up.
- Panels, gauge and finish
- We help you choose the panel profile, steel gauge and a factory paint finish. Better finishes such as PVDF coatings keep their color and resist chalking much longer than basic paint.
- Trim, flashing and penetrations
- Ridge caps, eave and rake trim, chimney flashing and pipe boots are fitted to the panels so water has nowhere to sit. These details decide whether a metal roof performs.
- Snow guards where they help
- Metal lets snow slide off in sheets. Over entries, walkways and lower roofs, we recommend snow guards so it releases in a controlled way.
- Cleanup and magnetic sweep
- Metal work leaves screw and trim scraps behind. We run magnets over the yard and driveway and haul away all debris before we leave.
Signs Metal Roofing Belongs in Your Plans
Your shingles are in their last years
Curling edges, bare patches and granules in the gutters mean replacement is coming. That is the window to price metal against shingles calmly.
Ice dams keep returning
If icicles and water stains show up every winter, a metal roof with proper eave protection sheds snow faster and gives ice less to grab.
Wind keeps lifting shingles
Repeated shingle losses after spring storms add up. Locked standing seam panels hold far better in high wind.
Your metal roof leaks at the screws
On older exposed-fastener roofs, the rubber washers dry out and crack. We can replace fasteners, or plan a new roof if the panels are rusting through.
The finish is faded or chalky
Dull, powdery paint means the coating is breaking down. It is not urgent, but it is a good reason to plan the next step.
How a Metal Roof Project Runs
- 1
Free roof inspection
We look at your roof, attic ventilation and decking from inside and out, take measurements and photos, and talk through how long you plan to stay in your home.
- 2
Written estimate and planning
You get a line-item estimate covering panels, underlayment, trim and any deck repair. We can lay standing seam, exposed fastener and shingles side by side, and we offer financing if spreading the cost helps.
- 3
Ordering and scheduling
Panels are usually fabricated to the exact lengths your roof needs, so they take a while to arrive. Starting early means we can place the order, pull the permit and hold a dry stretch of weather for your install.
- 4
Installation
We protect your landscaping, tear off and dry in the roof on the first day, then set panels and trim over the following days depending on the roof's size. The site is tidied at the end of each day.
- 5
Final walk-through
We check every seam, flashing and fastener, finish the magnetic sweep and walk the property with you before calling the job done.

How a Metal Roof Gets Priced
We build your price from measured roof areas and the exact system you pick, never from a rough guess per house. The free inspection gives us those numbers, so the written estimate you receive is one you can plan a budget around, with each line spelled out.
- Panel system
- Standing seam runs higher than exposed-fastener panels because of the concealed clips, heavier trim and extra labor. In return, it asks for far less upkeep over the years.
- Gauge and finish
- Heavier steel and premium paint coatings add to material cost, but they stand up better to dents and fading.
- Roof shape
- Valleys, dormers, skylights and steep pitches call for more cutting, more trim and slower work. A plain gable roof is the most economical to cover.
- Decking condition
- Any rotted or damaged decking must be replaced before panels go down. We photograph it and price it by the sheet, so nothing appears on the bill you did not see first.
- Extras you choose
- Snow guards, new gutters and added ventilation are optional lines on the estimate. We explain what each one does so you can decide what belongs in this project and what can wait.
Metal Roofing Questions
Something not covered here? (317) 751-7467
Will rain sound loud on a metal roof?
Over solid decking and underlayment, which is how we build every metal roof, rain is quiet. Most homeowners notice little difference from shingles. The drumming people picture comes from panels screwed straight onto open framing, like an old barn.
Will hail dent a metal roof?
Large hail can leave cosmetic dents, especially on thinner panels. Heavier gauges and textured finishes hide them better. If a storm does damage your roof, we work with homeowners and insurance companies on storm damage claims.
Can metal go over my existing shingles?
Sometimes, though we usually recommend removing them. Taking off the old layer lets us check and repair the deck and set proper ice protection at the eaves. We walk through the tradeoff for your particular roof during the inspection.
How far ahead should I plan a metal roof?
A few months is ideal. Panels are made to your measurements, and dry-weather install dates go quickly in spring and fall. An early inspection leaves time to compare options and set money aside.
Do you offer financing?
Yes, we offer financing. We can go over it alongside your estimate, so you see how a metal roof fits your monthly budget before you commit to anything.

Start Planning Your Metal Roof
A free inspection tells you what your current roof has left and what metal would involve. You leave with photos, honest advice and a written estimate to plan around.